Pneumatic high pressure pump. Diaphragm Pneumatic Pump
Pneumatic type pumps are oftenare used for pumping the pistons. Also, models are produced specifically for rifles. The principle of the device is based on a gradual increase in pressure inside the plunger mechanism. A spring is used to hold the rod.
Directly plunger mechanism is locatedon the stand. Handles for models are used in different widths. The hose has an average length of 45 cm. Many modern modifications are equipped with pressure gauges. The limit pressure parameter is at least 250 bar. The air pump weighs about 2.3 kg. The price for it fluctuates around 15 thousand rubles.
Modifications of diaphragm type
Pumps of this type are distinguished by the presencedouble sided plunger mechanism. Pushers in many modifications are used disk type. It is also important to note that models are in demand in the industrial sphere. On average, they are able to withstand a pressure of 300 bar.
The length of the rods is 35 cm on average. Most often in the market are sold three-stage pumps. The locating pins are located above the plunger mechanism. Weigh a lot of modifications. It is also important to note that most devices are manufactured with manometers. The racks of the models are soldered in different widths. It will cost an average pneumatic pump of this type in the region of 20 thousand rubles.
Devices for rifles
Pump (pneumatic) for rifles is differentits compactness. Rods for models are often made of aluminum alloy. In the upper part of the body there is a protective cap with a thread. If we talk about the parameters of the pumps, it is important to note that the operating pressure of the system is at least 250 bar. On the market, as a rule, two-stage modifications are presented.
The manometers are located at the bottomhousing. Pushers in devices are equipped with special adapters. Handles manufacturers make with rubberized overlays. Buy a model in stores can be priced from 13 thousand rubles.
Modification for servicing pistons
Pumps of this type are characterized by increasedparameter of the limiting pressure. This indicator on average fluctuates around 310 bar. The bars in the devices are about 45 cm long. Many modifications are equipped with pressure gauges. In this case, digital devices are rare. On average, the weight of the model does not exceed 3 kg. The locating pins in the devices are above the plunger mechanism. It is also important to note that models have an injection timing coupling.
It is produced most often from steel. Handles are produced in different widths. Racks, as a rule, are made C-shaped. Some models have special filters. For servicing the modifications, kits are often included in the kits. It is worth a pump (pneumatic) of this type no more than 20 thousand rubles.
Pumps for pumping
Pumps for pumping liquids arein demand in the industrial sphere. In this case, the casings are installed in a cylindrical shape with a double wall. Many modifications can boast of a high working pressure parameter. Rods for models are used with screw-type screwdrivers.
The pushers are installed directly above theplunger mechanism. Some pumps have a sealing bushing. It is also important to note that the market has modifications that have a bar length of more than 60 cm. Weigh a pump (pneumatic) of this type about 3.3 kg, and you can buy it at a price of 13 thousand rubles.
Model for oil
Pumps of pneumatic type for oilare made with adapters and without them. It is also important to note that there are modifications with a return spring. Plunger mechanisms in the devices are located in the lower part of the structure. At many models the length of the case does not exceed 40 see On the market three-step updatings are more often presented.
The weight of the pump of this type does not exceed 3 kg. Handles are often made with rubberized pads. The pushers in the devices are of disk type. If we talk about the parameters, the operating pressure of the three-stage modifications is 300 bar. Manometers are installed in almost all models. If we consider two-stage pumps, then they can withstand the maximum pressure at around 230 bar. Buy a model can be priced from 12 thousand rubles.
Said high pressure air pumpis made with brass valves. The working pressure parameter in the system does not exceed 300 bar. Pushers are commonly used disk type. It is also important to note that the plunger mechanism is installed on a special gasket. The filter for drying is not available in this case. A standard set of modifications includes a set of keys for maintenance. The mass of the device in assembled form is 2.7 kg. Buy this model the user is capable for 14 thousand rubles.
Pump (pneumatic) of this series is producedwith a wide handle. The case is made of aluminum alloy. The pushers in the devices are located above the plunger mechanism. The rack is wide, and it's comfortable to use. If we talk about the parameters, then the modification weighs exactly 27 kg, and the working pressure does not exceed 270 bar. To buy a pump (pneumatic) of the specified series in shops it is possible at the price from 13 thousand rbl.
Pump (pneumatic, manual) of this seriesis made in the factory with a sealing bush. This model is classified as a two-stage modification. Lubrication on the rod due to the protective ring lasts a long time. A standard set of models includes a set of keys for maintenance. In the upper part of the case there is a special lid with a thread. Weigh this pump of pneumatic type 2.3 kg. The manometer is located near the counter. It is also important to note that the device is equipped with a filter for drying. The length of the hose equals exactly 35 cm. The sealing bushing in the device is attached to the gasket.
The locating pins in the housing are above theplunger mechanism. In this case a small diameter is used. Directly the return spring is attached to the pushers. The adapter in this pump is pneumatic type cam-type. To advance the injection a special coupling is used. The body of the model is made in the form of a cylinder, and its diameter is 4.5 cm. The handle in the presented modification is not very wide, however it is comfortable to use. Buy this pump in stores can be priced from 15 thousand rubles.
Features of Umarex pumps
This pump (diaphragm, pneumatic)is made with a short barbell. A distinctive feature of the modification is considered to be solid pushers. Also, the model uses special rubberized lining. The case in this case is made of aluminum alloy. To advance the injection, a coupling is used as standard.
The adapter is located above the plungermechanism. According to the documentation, the pump can withstand a pressure of 310 bar. The return spring of the model is set to a small length. Directly the fitting over the plunger mechanism is fixed on the rod. To prevent its wear, there is a small sealing bushing. There are no filters for drying in this pump of pneumatic type. The weight of this model is 3.2 kg, and the height of the device is only 55 cm. You can buy it in the store for 15 thousand rubles.
Description of the device "Norika"
This oil pump (pneumatic) is made withwith a mechanical manometer. In this case, the working pressure parameter is 280 bar. The plunger mechanism in the device is located on a steel base. The upper part uses a protective cover. The bar in the device is solid and loads can withstand large ones. The length of the hose is 45 cm.
The height of the pneumatic pumptype is 53 cm. The handle of the modification is made with overlays. The sealing bushing above the plunger mechanism is without gasket. This model is worth about 13 thousand rubles in stores.